Recent content by TRON
-
Clutch Thread
I agree on the basic principle of batches and having a few bad apples but I don’t think 1k miles on this particular CM product is enough time to be giving any positive reviews. The failures are happening in the 5k-15k mile range. Regardless, curious what you long time members have to say that...- TRON
- Post #175
- Forum: Stock Performance/Mechanical
-
Clutch Thread
Speaking of clutches, how are those CM hydro bearings working out? Quite a few of us purchased them from the group buy on TW. And there have been quite a few who installed them and had leaking seals. Did you install yours @NHXRUNNER- TRON
- Post #173
- Forum: Stock Performance/Mechanical
-
-
What type plastic is the Body Kit?
Hey boys new and old. It’s been a long minute. Does anyone know the type of plastic our body kits are? Is it polyurethane? I’ve been looking for the best adhesive poxy so my kit stays nice and tight.- TRON
- Thread
- Replies: 3
- Forum: Exterior Modifications
-
What Did You Do To Your X-Runner TODAY?
Yup. I remember that too. I know NST probably still has these idler pulleys for other cars. And It’s a common size. Getting in touch with them is another story all together.- TRON
- Post #20
- Forum: General Off-Topic Discussions
-
What Did You Do To Your X-Runner TODAY?
I cooked my NST Kit idler pulley and bearings today. And completely shredded my SC belt. Anybody got an extra idler pulley for the NST overdrive Kit lol?!- TRON
- Post #18
- Forum: General Off-Topic Discussions
-
NST TRD Overdrive Kit question
This forum isn’t like it was 10 years ago but it’s a shot in the dark someone may know the answer. Does anyone know the product number for the pulley that fits 6303-2rs bearing for nst TRD Kit. I would like to get a new pulley since my bearing ceased today and messed up the pulley. Anyway...- TRON
- Thread
- Replies: 3
- Forum: F/I Mods & Tuning
-
We are still here!! New spoiler designs and new products coming soon!
Looks good man. Anybody have a pic where this spoiler meets up to a bed cover? Think my cover is about 3/4 inch above top of tail gate.- TRON
- Post #8
- Forum: Strictly Street
-
URD throw out bearing install/tips pics.
Yup. I don’t think it’s the TOB cause I have to almost completely engage the clutch pedal to the floor before the noise goes away. The humming is very slight and many people probably wouldn’t notice but it usually goes away after the engine completely warms up. It could just be “gearbox...- TRON
- Post #17
- Forum: Stock Performance/Mechanical
-
URD throw out bearing install/tips pics.
Has anyone experienced a slight humming sound at idle after installing the steel sleeve kit? The sound goes away only if you engage the clutch pretty much completely.- TRON
- Post #14
- Forum: Stock Performance/Mechanical
-
XMPLRY 2015 TRD supercharged
You should go down in size and get the quick change pulley 2.7 2.6 2.5. Alot of people on tacomaworld are running it on the TRD reflash- TRON
- Post #145
- Forum: Member Builds
-
Trd sc 50 shot vs 5.0 mustang
I've raced many coyote engines ... I take them from the start... But, I bet the high elevation and they all being NA gives me that one up ☺️- TRON
- Post #6
- Forum: Street Stories
-
TRD(Magnuson) S/C Quick Change Pulley
I don't know of anyone having a 2.6 or smaller pulley running around with only a 255 fuel pump and TRD injectors especially at sea level. That guy on tacomaworld might wanna be checking his #5 and #6 spark plugs often. I can't believe his afrs are good since he has 2 stock cats up stream from...- TRON
- Post #12
- Forum: F/I Mods & Tuning
-
Trd/magnuson charger
This is about 30,000 miles on 2.7 and NST and another 20,000 with the 2.55 and NST- TRON
- Post #30
- Forum: F/I Mods & Tuning
-
Trd/magnuson charger
- TRON
- Post #29
- Forum: F/I Mods & Tuning
